Dascom DP-520 Operator's Manual download pdf

DP-510/520 Quick Setup Instructions

Before Using Your Printer:

• Refer to Figure A to become familiar with the features of the DP510 or DP520 printer.

• Connect the Battery – (Refer to Figure B)

1. Remove the screw from the battery compartment door.

2. Push down and slide off the battery compartment door.

3. Plug the connector on the battery cable into the connector on the printer.

4. Make sure the battery cable is routed so that it will not be pinched when the door is installed.

5. Reinstall the battery compartment door and replace the screw.

• Charge the Battery – (Refer to Figure A)

1. Connect a Dascom

™

trickle charger (sold separately) to the appropriate power source and plug the cable into the printer’s Power

Connector as shown in Figure A. The charger may also be connected at the back of the DB9 connector of the optional RS-232 Serial

Cable.

2. The Status Indicator will flash orange indicating that the battery is being charged.

3. The battery will charge in 15 hours. The printer should not be used during this time.

• Load Paper – (Refer to Figure C)

1. Slide the paper lid release button toward the front of the printer until the lid opens.

2. Place the paper in the paper compartment with a small amount of paper extending from the top of the printer.

3. Close the paper lid until it “snaps” closed.

• Perform a Self Test – After the battery has fully charged, “double-click” the Paper Feed button.

• Attach the Belt Clip/Wall Mount – (Sold Separately, Refer to Figure D):

1. Remove the two “breakouts” using a small screwdriver.

2. Insert the Belt Clip/Wall Mount Bracket into the four holes on the back of the printer.

3. Slide the bracket toward the front of the printer until it “snaps” into place. The bracket may be removed from the printer by using the

Printer Release tab.

4. Place the Belt Clip over a belt as shown. The supplied machine screw may be used for additional security (requires removal of the

battery compartment door screw).

––– OR –––

Fasten the bracket to a wall using the supplied anchors and self tapping screws before attaching the bracket to the printer.

Notes:

• Use Only Dascom Battery Chargers.

• The battery must be fully charged as described above prior to first use.

• Maximum Battery Capacity is first reached after completing three complete charge and discharge cycles.

• Always use Genuine Dascom Paper & Labels to ensure optimal performance.

For more information, refer to the DP-510/520 Operator’s Manual. You may download this manual at www.dascomamericas.com.

Dascom Americas

421 West Main Street

Waynesboro, VA 22980

877- 434-1377

Dascom is a registered trademark of Dascom, Inc.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

IrDA is a registered trademark of the Infrared Data Assoc.

Figure B

Figure C

Belt

Printer Release Tab

Status

Indicato

Paper Lid Release

Paper Lid

DP-520

DP-510

IrDA Window

Paper Feed Button

Figure A

Wall Mount

Figure D

1 2

Summary of Contents

Page 1

DP-510/520 Quick Setup Instructions Before Using Your Printer: • Refer to Figure A to become familiar with the features

Page 2 - Status Indications

Operating Modes Interfacing The DP-510 and DP-520 printers have three operating modes, when not actually printing: • "Idle Mode": ready t

Dascom DP-520 Operator's Manual

Browse online or download Operator's Manual for Print & Scan Dascom DP-520. Dascom DP-520 Operator`s manual User Manual

Summary of Contents

More documents for Print & Scan Dascom DP-520

Comments to this Manuals

Dascom DP-520 Operator's Manual

Browse online or download Operator's Manual for Print & Scan Dascom DP-520. Dascom DP-520 Operator`s manual User Manual

Summary of Contents

More documents for Print & Scan Dascom DP-520

Comments to this Manuals

Related products and manuals for Print & Scan Dascom DP-520