Dascom T5040 Quick Start Guide User Manual

nQuick Start Guide T5040 Matrix PrinterU1-en-DascomTally.fm Seite 1 Samstag, 19. September 2009 2:29 14

Installation Quick start guide6` Placing the printer Place the printer on a solid, flat, surface, ensuring that the printer is positioned in such a wa

Quick start guide Installation7ENGLISH` Checking the printer voltageMake sure that the device has been set to the correct voltage (e.g. 230 V in Europ

Installation Quick start guide8` Switching on the printerPress the power which is located at the front bottom right of the printer switch for switchin

Quick start guide Control panel9ENGLISHControl panel The control panel consists of three keys for controlling the printer functions, four LEDs display

Operating the printer Quick start guide10Operating the printer` Inserting a document Before inserting a document make sure that the printer is switche

Quick start guide Operating the printer11ENGLISH` Inserting a passbook Before processing a new vertical-fold or horizontal-fold passbook, you should e

Operating the printer Quick start guide12The bulge of the opened passbook should be as flat as possi-ble to ensure trouble-free transportation into th

Quick start guide Operating the printer13ENGLISHWhen the passbook is inserted, the message ONLINE PAPER is displayed on the LCD. Do not use passbooks

Service and Maintenance Quick start guide14Service and Maintenance` Replacing the ribbon cassetteMake sure that the printer is switched off before rep

Quick start guide Service and Maintenance15ENGLISHRemove the colored ribbon guide from the print head by pull-ing it downwards.Raise the front end of

This device fulfils the European standards requirements by complying with the Directive of the Commission dated May 3, 1989 (89/336/EEC) relating to e

Service and Maintenance Quick start guide16Take the new ribbon cassette from the packaging and lift the ribbon guide from the cassette. Remove the tra

Quick start guide Service and Maintenance17ENGLISHPull the ribbon guide under the print head. Tighten the ribbon by turning the tension gear in the di

Service and Maintenance Quick start guide18Close the main frame by pressing the colored section in the middle of the frame as shown and ensure both le

Quick start guide Service and Maintenance19ENGLISH` Printing the Status Page The printer has a function that allows you to printout the current parame

Technical data Quick start guide20Technical data` Printer specificationsFor more information on printer specifications as well as interface specificat

Quick start guide Technical data21ENGLISH` Paper specifications Only use paper that corresponds to the paper specifications and test new sorts of pape

Technical data Quick start guide22` Consumables and accessoriesOnly use ribbon cassettes from the manufacturer as products from other manufac-turers m

“All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explic

© September 2009 DASCOM Europe GmbH 043398cGERMANYDASCOM Europe GmbHHeuweg 3D-89079 UlmDeutschlandTel.: +49 (0) 731 2075 0Fax: +49 (0) 731 2075 100www

Quick start guide Table of contentsIENGLISHTable of contentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Symbols used.

Quick Start-en.book Seite II Dienstag, 5. Dezember 2006 10:48 10

Quick start guide Introduction1ENGLISHIntroduction This Quick start guide is intended as a quick introduction into working with the printer and also t

Introduction Quick start guide2` Using the Online CD-ROM First install the Adobe Acrobat Reader on your hard disk, unless the program has already been

Quick start guide Printer at a glance3ENGLISHPrinter at a glanceCoverPower switch (On/Off)Paper trayControl panelRibbon cassettePrint headRelease leve

Printer at a glance Quick start guide4Power inlet Parallel interface1st Serial interface2nd Serial interfaceUSB interfaceView from the rearQuick Start

Quick start guide Installation5ENGLISHInstallation` Unpacking the printer Place your packaged printer on a solid base.Make sure that the “Up” symbols